Supply Air Plenum Box и Return Air Box: полное сравнение
Подробное сравнение приточных пленумов и возвратных воздушных коробов: конструктивные различия, направление воздушного потока, требования к изоляции, варианты фильтров и правила подбора размеров.
1. What Is a Supply Air Plenum Box?
A supply air plenum box is a sheet metal enclosure that sits above a ceiling diffuser and connects it to the supply duct. Conditioned air — heated in winter, cooled in summer — enters the plenum through a round or rectangular neck collar on the top or side, expands inside the box to reduce velocity, and exits through the open bottom into the ceiling diffuser.
The supply plenum's primary job is velocity reduction and air distribution. Air entering through a 10" duct at 800 FPM needs to slow down and spread evenly across the entire 600x600 mm diffuser face. Without the plenum acting as an expansion chamber, the diffuser would blast air straight down in a narrow column instead of spreading it across the ceiling.
Key characteristics of supply plenums:
- Neck collar on top or side (connecting to supply duct)
- Open bottom (facing the diffuser)
- Insulation required for cooling applications (R-4.2 to R-6)
- Sealed joints to prevent conditioned air leakage into the ceiling void
- Typical air velocity at neck: 600-900 FPM
- Operating temperature: 55-65°F (13-18°C) for cooling, 90-130°F (32-54°C) for heating
2. What Is a Return Air Box?
A return air box does the opposite of a supply plenum — it collects room air and channels it back to the HVAC unit through the return duct. Warm, stale room air enters through the open top or grille-facing side of the box and exits through a neck collar connected to the return duct.
Return air boxes serve a critical but often overlooked function: providing a path for air to get back to the air handler. Without adequate return air, supply air pressurizes the room, making doors hard to open and forcing conditioned air out through every gap, crack, and unsealed penetration.
Key characteristics of return air boxes:
- Open top or grille-facing side (collecting room air)
- Neck collar on side or bottom (connecting to return duct)
- Insulation usually not required (air is at room temperature)
- Filter frame often included (1", 2", or 4" filter slot)
- Typical air velocity at grille face: 300-500 FPM (lower than supply for noise control)
- Operating temperature: 72-78°F (22-26°C) — room temperature
3. Side-by-Side Comparison
| Feature | Supply Air Plenum | Return Air Box |
|---|---|---|
| Function | Distribute conditioned air to room | Collect room air back to AHU |
| Airflow direction | Duct → Plenum → Diffuser → Room | Room → Grille → Box → Return duct |
| Neck position | Top or side (duct entry) | Side or bottom (duct exit) |
| Open face | Bottom (diffuser connection) | Top or front (grille connection) |
| Insulation | Required (R-4.2 to R-6) | Usually not required |
| Filter frame | No | Optional (1"/2"/4" slots) |
| Air velocity at face | 600-900 FPM (at neck) | 300-500 FPM (at grille) |
| Air temperature | 55-65°F cooling / 90-130°F heating | 72-78°F (room temp) |
| Condensation risk | High (cold surface in warm void) | Low (air near ambient temp) |
| Sealing requirement | Critical (conditioned air is expensive) | Important but less critical |
| Noise sensitivity | Moderate | High (return grilles often at ear level) |
| Typical quantity per building | 1 per supply diffuser | 1 per 2-3 supply diffusers |
| FOB price (595x595, uninsulated) | $7-18 | $6-16 |
| FOB price (insulated / with filter) | $11-32 | $9-24 |
4. Construction Differences
Neck Collar Position
The most visible construction difference is where the neck collar sits. On a supply plenum, the collar is on the top (for vertical duct drop) or upper side (for horizontal duct run in tight ceiling voids). On a return air box, the collar is on the lower side or bottom, oriented toward the return duct routing.
This difference matters for installation: a supply plenum installed upside-down as a return box would have the neck collar at the top, requiring the return duct to run above the box and then drop down — adding unnecessary elbows, static pressure, and cost.
Joint Sealing
Supply plenums must be sealed to SMACNA Seal Class A or B standards (all transverse joints and seams sealed) because any air leak means conditioned air escapes into the ceiling void, wasting energy. Return air boxes have lower sealing requirements (Seal Class C) because leaks pull ceiling void air into the return stream, which is less costly than losing conditioned supply air — though still undesirable.
In practice, supply plenum joints are sealed with mastic or closed-cell gaskets, and the neck-to-duct connection uses foil tape or mastic plus a mechanical fastener (sheet metal screws or draw bands). Return box joints often use just foil tape.
Insulation
Supply plenums for cooling systems must be insulated. The temperature difference between 55°F supply air and an 85-100°F ceiling void causes condensation on every uninsulated surface. Standard insulation is R-4.2 (25 mm fiberglass liner) for most commercial applications, or R-6 (40 mm) for high-humidity environments.
Return air boxes typically do not need insulation because return air is at room temperature (72-78°F), creating negligible temperature difference with the ceiling void. Exception: return boxes in unconditioned spaces (attics, parking garages, exposed rooftops) benefit from R-4.2 insulation to prevent heat gain that increases the cooling load.
Filter Frames
Return air boxes often include a filter frame — a slot that holds a disposable air filter where room air enters the box. This captures dust, pollen, and particles before they enter the return duct, protecting the air handler's coil and improving indoor air quality.
Filter frames add 25-100 mm to the box depth depending on the filter thickness:
- 1" filter (25 mm) — standard residential, MERV 8-11
- 2" filter (50 mm) — commercial standard, MERV 8-13
- 4" filter (100 mm) — premium commercial, MERV 13-16, longer replacement interval
Supply plenums do not have filter frames because the supply air has already been filtered at the air handler unit.
5. Sizing Differences
While both supply and return boxes match ceiling tile dimensions (595x595 mm, 295x595 mm, etc.), their neck sizing follows different velocity rules:
| CFM | Supply Neck (700 FPM target) | Return Neck (500 FPM target) |
|---|---|---|
| 150 CFM | 6" (150 mm) | 8" (200 mm) |
| 250 CFM | 8" (200 mm) | 10" (250 mm) |
| 400 CFM | 10" (250 mm) | 12" (300 mm) |
| 600 CFM | 12" (300 mm) | 14" (350 mm) |
Rule of thumb: size return necks one diameter increment larger than supply necks for the same CFM. Return air is noisier because the grille is often at ear level (wall-mounted) or directly above the occupied zone, and lower velocity = less noise.
For detailed plenum box sizing calculations, see our companion guide.
6. Installation Differences
Supply Plenum Installation
The supply plenum sits above the ceiling diffuser, resting on the T-bar grid or supported by threaded rods from the structure above. The duct connects to the neck collar using sheet metal screws and mastic sealant or draw bands. After connection, the entire outside surface is wrapped with insulation (if not factory-installed), and all joints are sealed.
Critical: The gap between the plenum box and the ceiling grid must be sealed with a gasket or foam strip to prevent conditioned air from leaking into the ceiling void instead of going through the diffuser.
Return Air Box Installation
The return air box is installed similarly, but the open face points toward the room (through the return grille). If the box includes a filter frame, orient it so the filter is accessible for replacement — usually from below, by removing the return grille.
Return boxes can also use the ceiling void as a return air plenum in some building designs. In this case, room air enters the ceiling void through a return grille (without a box) and travels through the open ceiling space to a central return duct. This approach saves the cost of individual return boxes and return ductwork but is prohibited in some jurisdictions and requires firestopping at all ceiling penetrations.
7. Cost Comparison
Return air boxes are generally 10-20% cheaper than supply plenums of the same size because they do not require insulation and have simpler sealing requirements. However, return boxes with filter frames can cost as much as insulated supply plenums.
| Configuration | Supply Plenum | Return Air Box |
|---|---|---|
| Uninsulated, no filter | $7-18 | $6-16 |
| R-4.2 insulated / 1" filter | $11-25 | $9-22 |
| R-6 insulated / 2" filter | $15-32 | $12-28 |
| Multi-neck (2 collars) | $14-38 | $12-34 |
For a typical 10,000 sq ft office floor with 40 supply plenums and 15 return air boxes, the total plenum cost (FOB China) ranges from $450-1,200 depending on insulation and filter requirements. This is typically 3-5% of the total HVAC material cost for the project.
8. When to Specify Each Type
Use a Supply Plenum When:
- Connecting a supply duct to any ceiling diffuser (every time — no exceptions)
- The HVAC system provides cooling (insulated version required)
- Even air distribution across the diffuser face is critical (offices, hospitals, clean rooms)
- Noise control is important — the plenum acts as a sound attenuator between the duct and room
Use a Return Air Box When:
- Connecting a return grille to a return duct through a ceiling
- You need point-of-use filtration (filter frame in the return box)
- The building design does not use a ceiling void return (ducted return system)
- Code requires a fire-rated ceiling and you cannot use the ceiling void as a return plenum
Use a Ceiling Void Return (No Box) When:
- Local code permits ceiling void returns
- The ceiling void is enclosed and fire-rated
- Budget is tight and you want to eliminate return boxes and most return ductwork
- Filtration is handled at the AHU, not at the return grille
9. Sourcing Both from Airwise
Airwise manufactures both supply plenums and return air boxes at our Dongyang, China facility. Our Plenums & Air Boxes catalog covers 180+ standard configurations with options for insulation (R-4.2, R-6), filter frames (1"/2"/4"), multi-neck configurations, and top or side entry.
Ordering supply and return boxes together eliminates coordination issues — same material gauge, same galvanization standard, same dimensional tolerances. Combined with our diffusers and grilles, you get a complete air distribution package from one manufacturer.
For projects requiring both types, we provide a combined BOM (bill of materials) with itemized pricing so you can clearly see supply vs return costs in your project budget.